all very accurate but I want to add that eveb if you want to resin print in your bedroom you wont be able to. It’s not only that it’s toxic but the smell is so strong that, at least for me, it’s impossible to be around it. My printer is outside in the garage and when it’s printing you can still smell it inside the house.
Common printing questions
Submitted 4 days ago by GrayBackgroundMusic@lemm.ee to 3dprinting@lemmy.world
https://lemm.ee/pictrs/image/4f555306-81c7-4d69-a560-0ecfc3c7e071.jpeg
Comments
MissJinx@lemmy.world 4 days ago
half_built_pyramids@lemmy.world 4 days ago
Lol the napping skeleton is the best, love when streamers just breathe in and play with that shit like it’s play doh
SkaveRat@discuss.tchncs.de 4 days ago
or the guy who put it in an airbrush to cover a part and smooth it
einlander@lemmy.world 4 days ago
Ok, but where do I put the ink?
tiredofsametab@kbin.run 4 days ago
I want to get started 3d printing, partially because I bought a house and farm and need to replace some little bits and bobs that don't necessarily need to be super strong. It just seems a bit too much to try to figure out right now.
0110010001100010@lemmy.world 4 days ago
I went a little crazy on 3d printing during covid. I had a single printer prior but purchased two more. I haven’t printed on ANY of them in like 2 years. I end up just printing stupid shit or because I go so long between printing wasting way too much time to get everything dialed back in. Now I don’t even know what my slicing settings were and I would have to probably start from scratch. I should probably just sell my printers…
Anticorp@lemmy.world 4 days ago
I printed a lot of custom stuff that I designed for specific uses in Fusion 360 when I got my computer, and for about two years afterwards. But I don’t have any more custom stuff that needs to be printed, and I don’t have a D&D group any more, so my printer has been sitting for about six months. I’d say it’s a success though, since I made everything I need, and it’ll still be there if I ever need anything else.
nezbyte@lemmy.world 4 days ago
Having a 3d printer is super convenient for any home or shop repairs I need to make. I have so many curtain spacers and custom hooks all over the place now. The key is to get some hours in Fusion or some other good CAD software so you can whip up custom parts in minutes. You may get it wrong the first few times, but a couple minutes of tweaks and then you have a new part printing while you go back to working on other stuff.
The Swedish Maker just put out a video about how transformative 3d printing has been for his workflow. youtu.be/p2bClWmKHRM
Ahardyfellow@lemmynsfw.com 3 days ago
That’s fair, there is a bit of information overload online when looking into it.
If you want my two cents, find the cheapest print with auto bed levelling (mingda magicians are good and cheap) and just start playing around.You don’t need to know much to start, and you learn what you need to as you encounter problems.
That’s how I got into at least, and now been printing for like 5+ years.
Zehzin@lemmy.world 4 days ago
I’ll have you know the Ender 3 I found dumped behind a tent near the Dyatlov Pass is working great
Carighan@lemmy.world 4 days ago
Do the models appear finished before you even start printing?
CrowAirbrush@lemmy.world 4 days ago
They have like 236 ender 3’s nowadays, ofcourse i’m not asking google as i’ll end up on some website that’s shilling for creality and completely ignores the other brands.
Duamerthrax@lemmy.world 2 days ago
Can google be used at all for any product recommendations anymore? Anyone with a buck to make is gaming the algorithm.
fhein@lemmy.world 1 day ago
No and I hate it :( Even if there are a few legit review sites still around it’s near impossible to find them among all the fake reviews being pushed by search engines
papalonian@lemmy.world 2 days ago
I usually just use it to find some sort of peer reviewed recommendations (ie YouTube reviews) - it’s usually pretty easy to tell there who’s being genuine
JusticeForPorygon@lemmy.world 4 days ago
Okay but like I was given an Ender 3 for free and idk where to go from there
Maybe the fact that the family member who gave it to me didn’t want it around anymore should have been a sign
SkyezOpen@lemmy.world 4 days ago
Make sure the screws are snug and the beams don’t move. Level the bed, Youtube how. Then get a micro SD card and a slicing program. Slice the model, save to card, insert in printer, hit print from file and select the file.
That’s like 95% of it. The other 5 is endless struggles and troubleshooting, but you can worry about that when it comes to it lol. Oh also keep filament dry.
Shdwdrgn@mander.xyz 4 days ago
People give the Ender 3 a bad rap all the time, but it’s honestly a great little machine. I far prefer it to the $2500 printer we have at work that has “automatic everything” and can’t easily be adjusted to manually correct its bad settings.
With that said, how far have you gotten with it? Do you have any software installed? Have you tried printing anything (and was it successful)? You didn’t give much clue as to where you’re stuck. Yes you need to take some time to learn how to fine-tune the settings, and yes it can be frustrating because there is SO MUCH to learn about 3D printing, but once you get over the hump you can start cranking out all kinds of fun things.
conditional_soup@lemm.ee 4 days ago
Not op, I got a free Ender 3 from a frustrated co-worker, and am now the frustrated co-worker. I’ve tried getting a new glass print surface, tried using glue sticks, tried changing print temps and speeds, tried levelling and re-levelling and re-levelling the bed, but I just can’t get the print to stick for love or money. It’s now been re-homed to the garage, as a parking obstacle for my bicycle.
spizzat2@lemm.ee 4 days ago
Not the person you responded to, but I had mine set up. I had the software installed, I (thought) I even had the bed leveled, but every print either failed to stick to the plate, or eventually stuck to the nozzle. I ended up with a lot of spaghetti. I got frustrated and decided to take a break. I’d come back to it fesh, and see what I could do.
… That was three years ago.
DumbAceDragon@sh.itjust.works 3 days ago
Honestly when it works it works wonderfully. Most of my problems with my ender 3 come down to me being a dumbass and not taking care of it properly, and/or just the nozzles they ship with it being cheap as fuck and impossible to cold pull.
No joke my first ever successful cold pull was 2 days ago, because I had finally gotten a decent set of nozzles.
If you want to get really serious about printing there are better options out there, but for the cost they really are awesome beginner printers. I mostly only dabble with printing, but my ender 3 pro that I got like 3 years ago has served me very well.
JusticeForPorygon@lemmy.world 4 days ago
Honestly, I haven’t even plugged it in, just looked at what model it was and saw it frequently got clowned on lol
barsquid@lemmy.world 3 days ago
I found a printer in the trash that I grabbed, it had motors and frame but no PSU and mainboard. Five years later it is in worse shape than it was because I took the extruder off. I like to make progress on stuff by just increasing the scope so that it is overwhelming.
lefixxx@lemmy.world 3 days ago
It’s the raspberry pi of printers. It’s good for hobbyist and as a learning platform. its very cheap to get/mod and find parts.
But it’s not reliable enough for someone who wants printed parts. People who know 3d printing will underestimate the knowledge needed to use one of them.
evlogii@lemm.ee 4 days ago
I’m laughing out loud at the skeleton picture! He seems happy about his prints! 😂
key@lemmy.keychat.org 3 days ago
So what printer should I be looking for when I rob graves?
Poot@discuss.tchncs.de 3 days ago
Where are these graves I can rob Ender 3s out of??
NotSteve_@lemmy.ca 3 days ago
Ok but why isn’t it smooth 😅? My layers look like that but I kind of just accepted it as I have a cheap printer
duckythescientist@sh.itjust.works 3 days ago
Consider post processing steps if you really need smooth parts. Sandable fillers, special paints, epoxy coatings, or just a bunch of sanding. I’ve had good luck with XTC-3D. It’s an epoxy you paint on that’s specifically designed for smoothing prints.
You could also consider a resin printer if you need smooth. They are their own can of worms, but the resolution and smoothness is good.
I usually just accept the roughness.
eyes@lemmy.world 3 days ago
Yep, you’ll never get it perfect, but a smaller layer height will make the steps less noticeable. Adaptive layer height in cura if you use that can help, but adds a mortal age to the length of the print.
lefixxx@lemmy.world 3 days ago
Lower layer height will make the steps smaller. In orca slicer you can use adaptive layer height to decrease layer height just on the top of the dome.
Choosing different printing orientation can be a solution.
ArcaneSlime@lemmy.dbzer0.com 3 days ago
I have the opposite problem, my prints stick to the bed too well, I can hardly get them off!
Dettweiler42@lemmy.world 3 days ago
Let the bed cool down all the way, ya little gremlin! If you absolutely can’t wait, put the bed on a tile floor and your print should pop off on it’s own pretty quick.
ArcaneSlime@lemmy.dbzer0.com 3 days ago
I do! Lol I’ve had a print stuck to my bed for the last 2 weeks.
lefixxx@lemmy.world 3 days ago
Chuck the bed tlin the fridge for 1-2 mins
ArcaneSlime@lemmy.dbzer0.com 2 days ago
I’ll give that a shot, thanks.
FiniteBanjo@lemmy.today 4 days ago
The reason that in the middle is happening is that the temperature is wrong, judging by the inconsistent thickness of extruded material and lack of adhesion. If it’s a high heat filament like PETG then the printer might be stopping and resetting because its got a heat sensor with a low upper limit.
half_built_pyramids@lemmy.world 4 days ago
What about the top right benchy?
FiniteBanjo@lemmy.today 4 days ago
For that one you need an old priest and a young priest.
Shdwdrgn@mander.xyz 4 days ago
Two printers were fighting for the same bed (one with black filament and one with white). Obviously the black printer won and finished the print perfectly.
stealth_cookies@lemmy.world 4 days ago
Filament too wet obviously /s
stealth_cookies@lemmy.world 4 days ago
Pretty much all the reasons I can’t stand most 3D Printing communities on the internet. Too much basic troubleshooting answered dozens of times already and not enough cool projects.
tal@lemmy.today 4 days ago
Make a wiki, point people at the wiki, I suppose.
One thing I did like about Reddit was the wiki feature.
morbidcactus@lemmy.ca 3 days ago
Could have a bot that links to a git wiki, or even just a sidebar with knowledge base stuff would be nice for that.
Shdwdrgn@mander.xyz 4 days ago
I bitched at someone on reddit about that once… Asked a similar common question and so I asked them if they even bothered LOOKING at the sub before they posted because that exact question had already been asked three times that day! There’s being lazy, and then there’s crap like this.
Thcdenton@lemmy.world 4 days ago
The printing next the door bedroom makes me hope it catches fire and I burn to death.
Steve@startrek.website 4 days ago
Don’t forget gatekeeper replies to honest newcomer questions
Carighan@lemmy.world 4 days ago
And the hounding if you don’t get a Bambu. Somehow “Bambu printing” and “3D printing” seem to be two different things now, given the cult-like fervor.
barsquid@lemmy.world 3 days ago
I want to hound people for getting a Bambu. Look at the bullshit we’re dealing with on 2D printers because they aren’t open source with standard parts.
SatyrSack@lemmy.one 3 days ago
Where do you see that?
Honytawk@lemmy.zip 1 day ago
While good printers, the amount of waste those Bambus produce just don’t make them feasible in my eyes. If you use 4 colours, they use about 44cm of waste and you haven’t even started printing.