Submitted 4 months ago by verstra@programming.dev to selfhosted@lemmy.world
I know that the answer is yes, I should, but outlets near the setup are not grounded (even though they look like they are) and I don’t want to have wires running though my living room.
The real question is what are potential problems ? Occasional system reboots? Permanent damage to PSU? Permanent damage to other components?
Permanent damage to PSU? Permanent damage to other components?
Or worst: permanent damage to yourself.
Without a ground there is nowhere for a surge to go, permanent damage is much more likely. Surge protectors or a UPS will not protect against surges at all without a ground.
There’s also no ground so the chassis may have enough voltage on it to cause a shock if you touch it. This could also damage components as they are not grounded and touching things can introduce high voltage from static electricity which will have nowhere to go.
Additionally if you have ethernet connected to it the system may end up grounding itself through the ethernet cable, if the device at the other side does have a ground, which could cause issues.
So it basically just means you have a much higher chance of damaging the parts, or injuring someone touching things.
I know that the answer is yes
I mean, there you go, and all of the above. I’d add in a pretty large fire risk too. I hear my battery backups kick in regularly, and we’re talking about enough power to equal a large appliance (at least in my case). It’s 100% worth it to move them to a grounded outlet.
Install GFCI plugs.
Buy a small, appropriately sized UPS.
Profit?
You are correct that this is technically in code and would protect against shock hazards in a neutral error situation but you also get the opportunity for the outlet to pop during the day when nobody is home and the battery to die.
We had a situation in our old house where someone who was technically correct but didn’t think it through had a gfci outlet upstream of the refrigerator outlet. Thankfully it popped while someone was home and we got everything corrected before we lost everything in the fridge.
You food should expire that quickly. It would take at least a day or two.
For sure, a fridge is a really bad one to be using on an actual ungrounded GFCI, exactly for the reason of risk of expired food.
I like my homeserver but if something trips and its offline for a while it’s not gonna ruin my day.
I mean it depends on the intensity of the surge, but basically you’d be making it so your PSU is unable to protect the devices from surges. The more sensitive the electronics, the more critical the ground is and CPUs are pretty darned sensitive among other things. And depending on the type of components in the PSU, “surges” also include things like inrush current. Basically, when you turn on a transformer or certain other devices, there is a surge of sometimes as much as 10 times the rated current to create the initial magnetic flux. Depending on the components, this excess energy may end up getting shunted to the ground to avoid pushing it through your electronics. So if it can’t do that, you likely will blow fuses a lot when switching the power on (hopefully there are fuses), or if you’re touching the case which is supposed to be grounded, you may end up getting that jolt.
Anyway, without grounded outlets, and especially if your electronics are cheaply made because many expect there to be grounding and don’t build in extra components to deal with not having a ground, you are likely to significantly reduce the life of your electronics, your life, or start a fire without even considering major surges. If you have a high-end PSU, you may never have a problem until that surge happens. How stable is your power? Because even a normally small surge combined with a cheap PSU, and no ground, is pretty likely to end up in damage to electronics at the best case.
The most important risk you face is if somehow mains voltage ends up contacting somewhere you get electrocuted and die.
There are 2 purposes of an earth ground: First it can be used as a reference for certain signals, such as microphones. Second, it can be used to protect against turning yourself into a sparker.
There is a clear separation between mains voltage and system voltages so it's typically not going to be a problem, but if a little wire ends up contacting the power supply case it can become energized and things start to get really bad.
Most of the electrical code where I live focuses on grounding as "Bonding", which is purely safety related for giving dangerous voltages a safe place to go.
Other question for anyone listening here: How can we check if an outlet is correctly grounded ? I live in a faily new appartment with good outlets, but maybe I should make sure they are OK ?
$10-15 will get you an outlet tester at just about every home improvement store. You plug it in and the three big LEDs light up and you compare it with the sticker on the device. Get one with a GFCI tester built in, when you press the button it will short to ground and if your receptacle has GFCI protection or is on a GFCI protected circuit should trip the GFCI protection.
Something like this
www.amazon.com/…/B01AKX3AYE/
or this
www.amazon.com/…/B01AKX8L0M/
Grab something like this: https://www.amazon.ca/Gardner-Bender-GRT-3500-Standard-Outlet/dp/B000NBDTQI
Do you have money to replace everything plugged into those outlets, and sufficient home insurance that also ignores such things? Then, no, I guess.
You don’t need to have wired across the room. You can put them through the wall like every other cable. If the wire tubes are not full, it isn’t very complicated. I put my Ethernet wires in the wall.
Run the ground into the ground. You can get metal wire that would work nicely.
Except in very rare configurations (i.e. not 99.9% of residential), you do not want to have multiple paths to ground within a system. All grounds should go to the tied ground/neutral bus in the main breaker panel, which then goes to earth via a ground rod or a clamp to a copper gas/water line, etc. Otherwise you can have current flowing in ways that the system isn’t designed for, which at the least can trip breakers and GFCIs, and at worst exceed the rating of the wires in a short condition and cause a fire.
Good to know
Except in very rare configurations (i.e. not 99.9% of residential), you do not want to have multiple paths to ground within a system. All grounds should go to the tied ground/neutral bus in the main breaker panel, which then goes to earth via a ground rod or a clamp to a copper gas/water line, etc. Otherwise you can have current flowing in ways that the system isn’t designed for, which at the least can trip breakers and GFCIs, and at worst exceed the rating of the wires in a short condition and cause a fire.
empireOfLove2@lemmy.dbzer0.com 4 months ago
It will not affect system stability, but… Surge protectors do not work at all without a ground wire to drop excess voltage to. Any kind of line voltage disturbance could kill every device.
If your house is entirely ungrounded you really should have an electrician come update it ASAP. Outlet grounds have been mandatory since 1971. The chances are high that wiring predating that code is still using old cloth-wrapped wire insulation or even knob&tube, both of which are huge fire risks as the insulation is decayed badly by now. It’s expensive to have all new wire pulled but it is necessary.
scrubbles@poptalk.scrubbles.tech 4 months ago
Yeah it’s pricey, very pricey, but the risks are just too high for a home not to be properly grounded anymore. Homeowners have had 50 years to do it, it’s time to get it done.
tburkhol@lemmy.world 4 months ago
Heh. House I rented was built before ubiquitous electricity. At some point, someone slapped a fuse box on the outside of the back wall and drilled a bunch of 1" holes in said wall to pass wiring. House was built on piers, so they just dragged wires around to places where they wanted outlets, which were mostly planted in the floor. Not a ground wire on site. I have no idea how they got away with renting that out, but it’s not like I called code enforcement, either.
empireOfLove2@lemmy.dbzer0.com 4 months ago
Absolutely. Don’t fuck with electrical.
mojofrododojo@lemmy.world 4 months ago
this will also cause resets and instability. have seen it first hand.
Revan343@lemmy.ca 4 months ago
Reminds me of a story about magic
aubeynarf@lemmynsfw.com 4 months ago
Surge suppressors do not drop extra voltage to ground. They selectively short out surges between whatever two conductors have a high potential between them.
No ground conductor means there cannot be a high potential between it and anything else!