If you know why this happens pls help.
Seems like the top right corner is getting really close to the nozzle. Could be levelling, yeah.
I’m not sure how the ender works, but on my mk3s, I’ve had gunk under the springboard that did something similar.
Is this happens becuase of levelling issue?
Submitted 18 hours ago by Helkriz@lemmy.world to 3dprinting@lemmy.world
https://lemmy.world/pictrs/image/01edd172-4077-420d-b5de-664dfb986bb9.jpeg
Comments
cadekat@pawb.social 18 hours ago
Helkriz@lemmy.world 18 hours ago
Thanks. I will check it. I believed I did the leveling correctly prior to printing.
dosdude@retrolemmy.com@retrolemmy.com 17 hours ago Ender 3 can be a bit finicky. Make sure to check all corners at least twice after leveling. When you level one side, another can be out of level again.
fhein@lemmy.world 16 hours ago
If your printer is fully stock, replacing the bed springs either with silicone spacers or stiffer springs can be a good value upgrade. Keeps the bed from unleveling itself while printing, and IMO it also makes the initial adjustment a tiny bit easier. A bed probe is an immense quality of life improvement though, if you can afford to spend a little more money, since it both compensates for less-than-perfect bed leveling and also for any unevenness in the bed surface.
On the subject of upgrades, stay away from the “all-metal extruder” which used to be popular on Amazon etc. The stock Ender 3/v2 extruder is poorly designed and breaks easily. The metal version of it doesn’t break, but it’s still has the same bad design. If you’re going to invest money in a new extruder there are better options.
DeadDigger@lemmy.zip 11 hours ago
So for me the big bad indicator is basically the upper right corner on the one hand it looks like it was squished to much on the other it looks like an adhesive issue on the last layers of the right side.So a few questions that pop up for me: How does the file look like? Is it maybe wrongly sliced and the last part is in the air? Did you do manual mesh bed leveling? Did you check the bed level from the gantry to the plate with a kaliper to make sure it doesn’t change height between prints (to much)? How old is you nozzle? Is it maybe partially blown?
neclimdul@lemmy.world 10 hours ago
I immediately noticed the floating extrusion. but when you said this i realized they where right next to each other. if thats a bad sensor the manual leveling might work but i wonder if theres something(probably a bit of filament waste) under the sheet causing it to ripple or the build plate isnt very flat.
a high spot during probing could cause havoc on the interpolation and i could see it causing something like this. manual leveling would kinda help that but that spot would still be a disaster.
DeadDigger@lemmy.zip 10 hours ago
Yeah it’s a weird thing that I would assume cones from bad slicing, a bad bed or bad mesh leveling. But this can have different reasons too
dual_sport_dork@lemmy.world 11 hours ago
Also my usual left field advice of making sure nothing is stuck to the underside of your build plate, nor trapped in between the plate and the bed. I’ve gotten bit by that one before, as I have recounted several times. Tiny scraps of filament trapped in between, or whatever. That will cause high spots in unexpected places.
papalonian@lemmy.world 18 hours ago
There does seem to be a leveling issue (based on the difference in bed adhesion on the four pieces), but I’m kind of having a hard time figuring out what’s going on with the band that goes around the outside. Can you upload a screenshot of what this looks like in your slicer? And is this just one layer?
Test_Tickles@lemmy.world 14 hours ago
Bed leveling is the first suspect, but I would also make sure that the x gantry doesn’t wobble, moves smoothly, and is level to the bed.
Check the y axis to make sure there’s no wobble and the bed moves smoothly. Also make sure the rest of the frame is tight and square and the belts are tight.
Leveling can be a pain to get right on the ender3, but loose screws, flat wheels, ect will make it impossible.
GreenKnight23@lemmy.world 5 hours ago
looks like not just leveling but possible warping of your print bed or z-wobble.