That is a gas connection. Screw the flex hose on there and put soapy water on the junction to check for leaks before you open the valve.
bought a gas dryer thinking we had a gas connection... is this it???
Submitted 3 months ago by pugsnroses77@sh.itjust.works to [deleted]
https://sh.itjust.works/pictrs/image/4473cc81-1d35-4488-9ac9-b58c1fd8d286.jpeg
Comments
deegeese@sopuli.xyz 3 months ago
InternetUser2012@lemmy.today 3 months ago
You’re not going to see any leak without it being turned on.
deegeese@sopuli.xyz 3 months ago
check for leaks before you open the valve
Put the soap on first, the open valve. Are you having a reading comprehension problem or being pedantic?
terry_jerry@sh.itjust.works 3 months ago
That’s a square tip plug. It could be a gas line, but ur not getting the drier hooked up to that thing.
deegeese@sopuli.xyz 3 months ago
Gas dryer, my man.
Cheaper to run than electric.
Septimaeus@infosec.pub 2 months ago
(Guessing the entire argument below is based on lexical ambiguity in English)
CrimeDad@lemmy.crimedad.work 3 months ago
Where does the pipe go?
RubyRhod@lemm.ee 3 months ago
This is the only response. If you truly can’t tell where tf it’s coming from, then start sniff testing and fuckin around with buckets.
Does traction work on lemmy same as reddit? Doots and comments make go up?
CrimeDad@lemmy.crimedad.work 3 months ago
I think users can just sort the comments by ‘top’.
Hikermick@lemmy.world 3 months ago
Follow the pipe and see what it connects to. If it connects to another pipe that is attached to a faucet it’s water. If it connects to another pipe that attaches to your furnace it’s gas
Cagi@lemmy.ca 3 months ago
Can you put a baaloon over the nozzle and turn it on to see what comes out?
Dkarma@lemmy.world 2 months ago
It’s a gas line. It has a plug. Remove the plug and install the flex line. If you don’t have a line you have to buy the installation kit for your specific dryer.
Hardware store may have a generic part.
Offbus@lemmy.world 3 months ago
Is that a plug i see there on the end? Have you considered removing it and opening the valve a little to see what comes out?
pugsnroses77@sh.itjust.works 2 months ago
its like kinda open on the bottom so not all the way plugged? kinda the main reason its confused me tbh ive never seen an attachment like it in my life
ikidd@lemmy.world 2 months ago
So that’s an NPT plug on the bottom. Hold the ring above the plug with one wrench and use another on the plug to unscrew it a bit. It’s painted over so it’ll be tough, though if you squeeze the two wrenches together it should come.
Just unscrew it a bit, and if the upper wrench is moving, stop and make sure you aren’t messing up the valve since if that ring comes off the bottom of the valve, you’ll have a hell of a time because the valve will drop apart.
If you crack the valve and smell gas, you have gas to that valve. Unless there’s another valve or that line is cut off, I would bet money that is gas. You will now need an NPT to flare fitting to put where that plug is, and an appropriate length flexible extension pipe from the dryer to the flare fitting. These are usually a yellow extension that you get at the hardware store. Get one long enough to be able to pull the dry our a bit and move it around, but not overly long. Use some gasline teflon tape (yellow again) or gas pipe dope to put the NPT adapter in, but don’t use anything on the flare fitting connections at the adapter and the dryer.
When you have everything hooked up, use soapy water and turn on the valve. If you see any bubbles at any of the connections, turn it off and tighten. It shouldn’t take all that much force to tighten a flare fitting so don’t go overboard.
If any of this confuses you, stop, watch some youtube videos, and if you’re still uncertain, hire a professional. Most plumbers can do minor gas fitting like this for you, you don’t need a gas installer.
Offbus@lemmy.world 2 months ago
It’s difficult to see from the picture provide what you might mean by “kinda open”. Can you provide a picture or may be an example of what is fastened to the valve body opposite the pipe? If you can’t, is what’s depicted in this link what you see? mcmaster.com/…/4627K333_Medium-Pressure Iron Pipe…
NOT_RICK@lemmy.world 3 months ago
Looks like one to me
superkret@feddit.org 3 months ago
If you don’t know, call someone who does.
ikidd@lemmy.world 2 months ago
This right here. If you have to ask this question before you trace a pipe back to it’s source and figure it out for yourself, you should not be fucking with gas lines.