Not too bad for my first ever try with TPU

Submitted ⁨⁨1⁩ ⁨month⁩ ago⁩ by ⁨bdonvr@thelemmy.club⁩ to ⁨3dprinting@lemmy.world⁩

https://files.catbox.moe/ksr7l6.heic

Lots of stringing but as I understand that’s normal for TPU. Printed at 225⁰C on a 30⁰ bed, stock Ender 3 S1. 0 retraction, 0.93 flow, 35mm/s for most speeds

source

Comments

Sort:hotnew top

papalonian@lemmy.world ⁨1⁩ ⁨month⁩ ago
Erm, it’s proper etiquette when posting TPU benchies to upload a picture in squished form 😉

Pretty decent looking print. This printer has a Bowden tube setup yeah? Impressive. If you decide to upgrade to a direct drive you’ll probably be able to print it with retraction and help tone down the stringiness.

source
- bdonvr@thelemmy.club ⁨1⁩ ⁨month⁩ ago
  No the S1 is direct drive. I tried a retraction tower to little effect but perhaps I’ll try a wider range.
  
  This one I accidentally printed with too many walls to squish much lol. I did another with one wall and no infill, came out the same appearance wise but squishes nicely.
  
  source
  - IMALlama@lemmy.world ⁨1⁩ ⁨month⁩ ago
    On my direct drive Voron I could make it through retraction tower test prints fine with TPU, but it would always jam with retraction enabled on longer prints with my usual 0.3mm. Pulling apart the extruder would always reveal some TPU had gotten wrapped around the drive gear. Rather than try tuning until the failure went away, I just went with 0 lol.
    
    source
- Prunebutt@slrpnk.net ⁨1⁩ ⁨month⁩ ago
  I thought the flexible benchie is the octopus?
  
  source
dual_sport_dork@lemmy.world ⁨1⁩ ⁨month⁩ ago
That’s better than my first attempt with TPU was, that’s for sure. No retraction whatsoever? That’s bold.

If your slicer supports it, I recommend enabling “combing” (which is what Cura calls it), or “Avoid Crossing Perimeters” (in Prusa/derivatives) which work slightly differently, but have the net effect of keeping the nozzle within the outer walls of the print during moves when possible, which ensures that any stringing so caused winds up inside the solid spaces in the model where it’s not visible.

source
- bdonvr@thelemmy.club ⁨1⁩ ⁨month⁩ ago
  I had read that TPU doesn’t really like to be retracted. I did a retraction tower and it didn’t seem to make any difference really at least in the ranges I tried. I have avoid crossing perimeters on (using OrcaSlicer) with something like 350% detour but that won’t help with the archway of course since those lawyers are just completely separate pieces
  
  I’ll have to try the combing setting though
  
  source
  - dual_sport_dork@lemmy.world ⁨1⁩ ⁨month⁩ ago
    The E3 S1 is a direct drive extruder, right? If so, it should produce some kind of results for you although in my experience you have to retract TPU pretty far to get results, like 5-6mm. In my experience it always oozes as least a little bit so long a your nozzle is at temperature and there’s any amount of the stuff in the chamber, so you’ll never fully eliminate stringing. But some retraction should help, and you can get it down to being very minor.
    
    On a Bowden type extruder, though, it’s basically a fool’s errand because the stuff is so damn elastic, and is also slightly compressible to boot. The more length of it you have between your extruder gears and the tip of your nozzle, the more its elasticity becomes apparent. I think this is where the “common wisdom” of no retraction on TPU came from. The stuff can kink and then jam in a Bowden tube if you really go at it with gusto.
    
    Anyway, you could also try a fairly long “wipe after retraction” setting.
    
    source
WoahWoah@lemmy.world ⁨1⁩ ⁨month⁩ ago
Everyone else: “The microplastics are killlling usssss!!1!”

3D Printer people: “I love the smell of carcinogens in the morning.”

source
- dual_sport_dork@lemmy.world ⁨1⁩ ⁨month⁩ ago
  Comes into a 3D printing sub.
  
  Insults 3D printing hobbyists.
  
  For your next trick, you should try going into a biker bar and loudly proclaiming that motorcycle riders are sissies.
  
  source
  - WoahWoah@lemmy.world ⁨1⁩ ⁨month⁩ ago
    You’ll be OK.
    
    source
- bdonvr@thelemmy.club ⁨1⁩ ⁨month⁩ ago
  The cancerousness is hugely dependant on what type of plastic you’re printing lol.
  
  source
  - dual_sport_dork@lemmy.world ⁨1⁩ ⁨month⁩ ago
    You can also vent your printer outside, which is what I currently do, using this.
    
    source
Imgonnatrythis@sh.itjust.works ⁨1⁩ ⁨month⁩ ago
I’m not able to load your Pic but I’ve found aggressive dehydration helps with tpu stringing. As with any residual stringing, a quick cleanup with a butane torch works well.

source
- SpaceNoodle@lemmy.world ⁨1⁩ ⁨month⁩ ago
  How would you suggest going about aggressively dehydrating it?
  
  source
  - Imgonnatrythis@sh.itjust.works ⁨1⁩ ⁨month⁩ ago
    Run it in a dehydrater for 6h prior and during print
    
    source
hsdkfr734r@feddit.nl ⁨1⁩ ⁨month⁩ ago
You’re the captain now.

source