Belt organizer

Comments

• Omgarm@lemmy.world ⁨1⁩ ⁨year⁩ ago

  Nifty! But I onky have 2 belts…

  source

  • thenewred@lemmy.world ⁨1⁩ ⁨year⁩ ago

    Clearly you need to buy more belts to fill out your new belt organizer

    source

    • alvvayson@lemmy.world ⁨1⁩ ⁨year⁩ ago

      And don’t forget to buy them in pairs so that the organizer remains balanced.

      source

      • -> View More Comments
    • RGB3x3@lemmy.world ⁨1⁩ ⁨year⁩ ago

      My wife bought me a 6-slot watch box last year when I only owned two watches…

      Obviously, I had to fill it up.

      source
• SamsonSeinfelder@feddit.de ⁨1⁩ ⁨year⁩ ago

  What if you have an uneven number of belts because you take one or put one away? It would be very instable and would tilt without the same weight front and back.

  source

  • Noite_Etion@lemmy.world ⁨1⁩ ⁨year⁩ ago

    That’s my thoughts too.

    This is just a suggestion, not a knock or anything against the poster. But a solution I think could work is rotate the hook 90 degrees and have 2 of them, one at each end. Then it would remain flat and balanced no matter where the belts are on the rack.

    source

    • FuglyDuck@lemmy.world ⁨1⁩ ⁨year⁩ ago

      I think I’d hang the hook off the end, so that the belts are stored in a vertical tree (slightly sloped, so that they don’t fall over each other.) But that’s an entirely new redesign for something that only really matters if you care about it.

      source
  • thenewred@lemmy.world ⁨1⁩ ⁨year⁩ ago

    There’s a little bit of movement but it’s not too annoying. When loaded up with belts, taking one off doesn’t make a big difference.

    source

    • karlach@lemmy.world ⁨1⁩ ⁨year⁩ ago

      What about a radial hanger? Hooks positioned at Fibonacci intervals spiralling outward. Would the weight be more evenly distributed toward the center?

      source

      • -> View More Comments
  • Denalduh@lemmy.world ⁨1⁩ ⁨year⁩ ago

    Buy a decoy belt that only gets used when you’re wearing one of the real belts. The decoy belt can get a wall mounted hook so it’s out of the way when no belts are being warn.

    source
  • MoonlitCringe@sh.itjust.works ⁨1⁩ ⁨year⁩ ago

    Just leave the empty gap in the middle? Come on Sam, we’ve got to work together on stuff like this!

    source
• crystalmerchant@lemmy.world ⁨1⁩ ⁨year⁩ ago

  What if you have only one belt

  source
• uninvitedguest@lemmy.ca ⁨1⁩ ⁨year⁩ ago

  What’s the solution for plaque buckles?

  source

  • thenewred@lemmy.world ⁨1⁩ ⁨year⁩ ago

    My personal solution was to not own any. But I have thought about it. Maybe a slot on both ends of the body to slide the knob of the buckle into. That would allow for two belts pretty easily.

    source
  • NewNewAccount@lemmy.world ⁨1⁩ ⁨year⁩ ago

    Had to google this. Are these common? I personally think they’re not very good looking.

    source

    • uninvitedguest@lemmy.ca ⁨1⁩ ⁨year⁩ ago

      Common? Not sure. They’re available at standard shops. I have had one for 20 years that I picked up in highschool from American Eagle for $34.50. Why is that etched in my brain? I was specifically looking for one at the time.

      I prefer the look (as long as it’s simple) and function.

      source
• Waraugh@lemmy.dbzer0.com ⁨1⁩ ⁨year⁩ ago

  I bought a tie hanger with hooks. It lets me hang up my four belts and ~10 ties (that I’ve never worn again since the rona). I’m usually in sweat pants and hardly use my belts anymore now that I think about it. Anyway, I really like it. Think this would have more Utility and use less material with just hooks.

  Mine looks like this one

  Image

  source
• uis@lemmy.world ⁨1⁩ ⁨year⁩ ago

  I would go with more slopes instead of fillets, but nice anyway

  source
• AdamHenry@discuss.tchncs.de ⁨1⁩ ⁨year⁩ ago

  I have one that I absolutely despise. It has only one job and it tosses my belts to the floor…on purpose.

  source
• Fredselfish@lemmy.world ⁨1⁩ ⁨year⁩ ago

  Another reason for me to buy a 3d printer. Any tips on building one folks?

  source

  • TheTetrapod@lemmy.world ⁨1⁩ ⁨year⁩ ago

    Buy an ender 3 if you’re cheap and have plenty of tinker time. Buy something by Bambu if you have cash and want ease of use.

    source

    • Fredselfish@lemmy.world ⁨1⁩ ⁨year⁩ ago

      I’m more broke but want to get one anyway and I am between the technical and ease of use mode.

      source
  • thenewred@lemmy.world ⁨1⁩ ⁨year⁩ ago

    Try to go with something popular so you can find help when things inevitably go wrong. Expect to learn a lot when building. If you like that, awesome, do it. Otherwise you may want to consider a prebuilt prusa or bambu.

    source

    • Fredselfish@lemmy.world ⁨1⁩ ⁨year⁩ ago

      What’s popular?

      source

      • -> View More Comments
  • grayman@lemmy.world ⁨1⁩ ⁨year⁩ ago

    How much money do you want to put into a setup? With $1000, you an get any of the really good printers, a different size nozzle, a few little tools, and plenty of filament.

    source