bought a glass too small for my fridge so I fixed it 3d printing

Comments

• technomad@slrpnk.net ⁨2⁩ ⁨months⁩ ago

  Hey, could you show us a bit more perhaps? It’s not very clear what you fixed exactly.

  source

  • moody@lemmings.world ⁨2⁩ ⁨months⁩ ago

    I think they meant a piece of glass. Looks like what would go on top of the cheese drawer in the fridge.

    source
  • AppearanceBoring9229@sh.itjust.works ⁨2⁩ ⁨months⁩ ago

    Had to make a second version because the one on the post was too fragile. It was bending with just the glass. The new one looks like this

    Image

    Image

    source

    • technomad@slrpnk.net ⁨2⁩ ⁨months⁩ ago

      Oh, nice fit! Are you pretty satisfied with it so far? I don’t imagine it would have any issues with the cold temps, and it pretty much looks like it came with the fridge. Good work!

      source

      • -> View More Comments
• Kolanaki@pawb.social ⁨2⁩ ⁨months⁩ ago

  Was confused by the title. “How do you have a cup too small for a fridge?”

  source
• PurpleClouds@lemmy.world ⁨2⁩ ⁨months⁩ ago

  Hope you seal that bad boy up or it’s going to be a nice home for all those microorganisms.

  source

  • AppearanceBoring9229@sh.itjust.works ⁨2⁩ ⁨months⁩ ago

    Yeah didn’t tought of that, do you think epoxy resin is enough?

    source

    • PurpleClouds@lemmy.world ⁨2⁩ ⁨months⁩ ago

      Food safe epoxy would be fine I think. Don’t get the cheap stuff.

      source
    • technomad@slrpnk.net ⁨2⁩ ⁨months⁩ ago

      Salt annealing!!! I just saw a video on this: nyc1.iv.ggtyler.dev/b5xcvbxhCvE?t=5

      source
• Hotspur@lemmy.ml ⁨2⁩ ⁨months⁩ ago

  This is the kind of shit that always sells 3d printing to me, when is see someone solve a whacky problem they have that otherwise would be kinda hard to pull off.

  I’m guessing that these days the filaments/resins are getting pretty high durability on the consumer market?

  source

  • myplacedk@lemmy.world ⁨2⁩ ⁨months⁩ ago

    3D printing is not as strong as injection molding the same material in the same shape.

    But you can beef it up. You can 3D print stuff much bulkier than injection molding can do.

    If you really want to, you can also use stronger materials.

    Also, even the weakest cheapo stuff you can get is plenty strong for most stuff people are printing.

    Knowing about what makes a part strong or weak helps a lot.

    source

    • Hotspur@lemmy.ml ⁨2⁩ ⁨months⁩ ago

      Yeah ok makes sense. Plus like you said you can always over build the piece, etc. and if it breaks after a few months, you can always reprint it haha.

      source

      • -> View More Comments
  • AppearanceBoring9229@sh.itjust.works ⁨2⁩ ⁨months⁩ ago

    The durability comes with the design and the material used. As I said on another comment the first version was very fragile and was bending with barely any weight on it.

    After adding a bracket to hold the glass in between it keeps its form even with food on top. It all depends on how you design the piece and in which direction you print. Not always the easiest way to print is the best for durability.

    source
• BrazenSigilos@ttrpg.network ⁨2⁩ ⁨months⁩ ago

  Id love to know how you got the first layer to stick, I couldn’t get my Cr-30 to print anything more then spaghetti.

  source

  • AppearanceBoring9229@sh.itjust.works ⁨2⁩ ⁨months⁩ ago

    At the beginning I had several issues. If I remember correctly first I has to level the front part, then mark the distance with a wedge and have that same distance on the back.

    For this it is important that when you’re adjusting the Y0 check on both edges and in the middle. It should be the same height overall

    Once it’s leveled you need to adjust the Y offset until it sticks, for this you can print a zigzag pattern and it should stick equally well everywhere.

    I remember I had saved some videos that explain that let me find them. Also the discord community is helpful for this particular printer

    source