Super Mario Warp Pipe tv remote holder

Comments

• Noite_Etion@lemmy.world ⁨1⁩ ⁨year⁩ ago

  Put a motion sensor in the pipe wired to a speaker that makes the warp noise each time it’s triggered.

  source

  • turkalino@lemmy.yachts ⁨1⁩ ⁨year⁩ ago

    Even simpler, an IR opto switch

    source
  • mooklepticon@lemm.ee ⁨1⁩ ⁨year⁩ ago

    Pressure switch in the bottom maybe?

    source
• j4k3@lemmy.world ⁨1⁩ ⁨year⁩ ago

  This would be a good one to sand and polish if you are ever inclined. All filaments can be polished. PLA is only second best to ABS/ASA in my experience. PLA will hold a shine that is about the same texture as factory Lego bricks.

  source

  • TwanHE@lemmy.world ⁨1⁩ ⁨year⁩ ago

    Abs/Asa can also be lightly sanded and then vapor smoothed.

    source

    • j4k3@lemmy.world ⁨1⁩ ⁨year⁩ ago

      They are very different processes. Vapor smoothing is more of a hack than anything. It traps the solvent in the part for a very long time. Like using acetone on auto body trim and bumpers that are mostly ABS will get you fired from any shop. It will bleed and ruin the top coat an clear coat as it vents from underneath them. In my testing, acetone greatly alters the structural strength as well. Polishing maintains or in some cases improves the mechanical performance of parts. Even for cosmetics, the polished part will look like it was injection molded while the inconsistency and rounded corners of vapor smoothing look very DIY. Polishing can be done poorly, and I am an actual finishing pro, so YRMV.

      source

      • -> View More Comments
• Papergeist@lemmy.world ⁨1⁩ ⁨year⁩ ago

  Tasting History by Max Miller. Excellent choice!

  source

  • mooklepticon@lemm.ee ⁨1⁩ ⁨year⁩ ago

    Haha thanks.

    source
• Everythingispenguins@lemmy.world ⁨1⁩ ⁨year⁩ ago

  I feel like this is a really good way to loose the remote in the basement

  source

  • mooklepticon@lemm.ee ⁨1⁩ ⁨year⁩ ago

    Bloop bloop bloop.

    Why does that turtle have the remote?

    source
• chemical_cutthroat@lemmy.world ⁨1⁩ ⁨year⁩ ago

  You know these already exist, right… No need to 3d print one…

  source

  • seiniku@lemmy.world ⁨1⁩ ⁨year⁩ ago

    It’s rewarding to make your own things

    source
  • CADmonkey@lemmy.world ⁨1⁩ ⁨year⁩ ago

    Just because of your silly comment, I’m going to make my own model of this, even though someomnr already has, and Im going to print it out. Why? Because those two things will cost less and take less time than ordering one.

    source

    • chemical_cutthroat@lemmy.world ⁨1⁩ ⁨year⁩ ago

      Yeah, good idea. Let’s use more plastic for useless fucking things. Or, maybe just go the fucking hardware store and buy it.

      source

      • -> View More Comments
    • Caillte@lemm.ee ⁨1⁩ ⁨year⁩ ago

      Here’s hoping you threw a little fillet on the top outer rim. That model was begging for a bit of a rounded edge.

      source

      • -> View More Comments