Help me identify a filament's material

Submitted ⁨⁨1⁩ ⁨day⁩ ago⁩ by ⁨ExtremeDullard@lemmy.sdf.org⁩ to ⁨3dprinting@lemmy.world⁩

I found a small length of filament in the parts bin. I don’t know what it is, and nobody here else does, or remembers ordering it. I’m pretty sure it’s a sample that was sent by Prusa when we ordered the printer, and it’s probably not a special material.

It’s feels “gummy” and a lot softer than PLA, but not really rubbery either. And I tried printing something with it at 230C as if it was PLA and it’s clearly not hot enough: it’s able to flow out of the nozzle but it barely sticks to the bed.

Any idea what it could be?

source

Comments

Sort:hotnew top

Manzas@lemdro.id ⁨1⁩ ⁨hour⁩ ago
FLEX or NYLON I would guess

source
moody@lemmings.world ⁨5⁩ ⁨hours⁩ ago
Could be some sort of purge filament. They’re meant to be run at high temperatures and forced through the nozzle so that they can flush out any leftover material stuck inside.

source
- ExtremeDullard@lemmy.sdf.org ⁨3⁩ ⁨hours⁩ ago
  Interesting… I didn’t know purge filament existed. In fact, I wondered what would happen if I ever ran something that truly gummed up the nozzle, if I’d have to replace it entirely or something.
  
  source
j4k3@lemmy.world ⁨23⁩ ⁨hours⁩ ago
TPU if it is soft and like gummy/rubbery

I use the stuff for seals some times, but more often it makes the perfect string for cat toys. Put a length on a stick, add some painter’s tape on the end, and wave it around; cats go nuts.

source
- ExtremeDullard@lemmy.sdf.org ⁨21⁩ ⁨hours⁩ ago
  Lol
  
  Clearly that’s progress 🙂
  
  source
KickMeElmo@sopuli.xyz ⁨23⁩ ⁨hours⁩ ago
Need to know what material your build plate is made of to guess what wouldn’t stick to it.

source
dual_sport_dork@lemmy.world ⁨18⁩ ⁨hours⁩ ago
Well, if we’re ruling out PET and PETG – PET would probably require the temperatures you describe and would be impervious to acetone, as well as extremely flexible – there is an outside possibility it could be HDPE.

HDPE filament is damn rare, though, and I’d doubt anyone would be giving it away as samples given how difficult it’d be to print with most consumer machines. HDPE’s signature tell is that it feels somewhat waxy if you e.g. scrape at it with your fingernail.

source
ExtremeDullard@lemmy.sdf.org ⁨21⁩ ⁨hours⁩ ago
Well, I toyed with the printer’s temperature settings until I found a combination of nozzle temperature and bed temperature that finally made it spew out parts.

It seems to flow best at 260C, but then when it lends on the bed, it immediately shrinks as it cools and the part curls up and comes unstuck. I had to lower the temperature to 245C and raise the bed temperature to the maximum this printer does - 110C - for the part to stick enough to complete.

The nozzle clearly isn’t hot enough because some layers on the final parts look like they’re about to delaminate. But any hotter than that and the material curls up. And it doesn’t matter what bed plate I use: that stuff doesn’t seem to stick to anything properly.

I printed spectacles with that mystery filament. You can see how floppy it is here:

toobnix.org/w/qJJ1htb9eqmiHx7gSpq2RT

It looks like TPU alright, but the temperatures involved aren’t really typical of TPU. Also, acetone does nothing to it whatsoever.

The material also doesn’t like to be filed or sanded, and the best results for a nice finish without bits of material sticking out all over the place is to “polish” it by running a very sharp x-acto blade across the surface until all the junk is gone and the surface is shiny.

Weird filament. Kind of useless…

source
- IMALlama@lemmy.world ⁨8⁩ ⁨hours⁩ ago
  It might be TPU too. I’ve used it to print function tires and the random deformable fidget.
  
  source
  - ExtremeDullard@lemmy.sdf.org ⁨3⁩ ⁨hours⁩ ago
    The more I look at it, the more I think that is in fact TPU. And in fact I’ve read somewhere that most varieties of TPU are in fact impervious to acetone. The one roll I have here isn’t, but maybe this yellow piece is such a kind.
    
    source