Mr_Mofu
@Mr_Mofu@lemmy.blahaj.zone
Soft Things Lover
- Comment on How do you Sand Coloured PETG without loosing the Colour? Are there any Methods to Preserve or Regain the Colour? 4 days ago:
I mean it wasn’t boiling which I thought was the issue. The setup I got rn is a Very Solid glass Jar that was fully Sealed and heated to around 50°C on my Printer bed. Left my Prints in there for between 30 Minutes to a Whole day, and while it was a lot shinier afterwards, no changes in the lines or or layers where to be seen.
Safety wise I got a Gas Mask, Fitting Clothes and some other Saftey stuff around
- Comment on How do you Sand Coloured PETG without loosing the Colour? Are there any Methods to Preserve or Regain the Colour? 4 days ago:
Hmmm my Heatbed goes to 100°c and I do have a Smooth surface plate around… what do you think?
- Comment on How do you Sand Coloured PETG without loosing the Colour? Are there any Methods to Preserve or Regain the Colour? 4 days ago:
I have tried using a Regular Soldering Iron to smooth out the surfaces, to not a lotta luck tho. At what temps can the Plastic Colouring be regained? Because I think I had mine set too high
- Comment on How do you Sand Coloured PETG without loosing the Colour? Are there any Methods to Preserve or Regain the Colour? 4 days ago:
The Shiny look it something I try to somewhat avoid im afraid
- Comment on How do you Sand Coloured PETG without loosing the Colour? Are there any Methods to Preserve or Regain the Colour? 4 days ago:
The main thing I’m wondering right now, is the MEK supposed to Boil? I feel like it should be, but at that point im also working with e Pressurised Vessel with very much Dangerous chemicals… thought’s?
- Comment on How do you Sand Coloured PETG without loosing the Colour? Are there any Methods to Preserve or Regain the Colour? 5 days ago:
The Prints I’m working on at the moment are rather small, I think a Torch or Heatgun could also melt other spots that aren’t supposed to be melted because of needed Surface Patterns… I wonder if there is something a bit more Controlled?
- Comment on How do you Sand Coloured PETG without loosing the Colour? Are there any Methods to Preserve or Regain the Colour? 5 days ago:
I have been using more Coarse ones thus far yes… I do wanna achieve the same colour as the original Plastic tho
- Comment on How do you Sand Coloured PETG without loosing the Colour? Are there any Methods to Preserve or Regain the Colour? 5 days ago:
I see, thats quite interessting… I do wonder since my Main Concern are Flat Top Surfaces, if putting the rough Print surface on a Heated Surface of Sorts would do something simular? Thinking like a Heated Pan or Metal Sheet?
- Comment on How do you Sand Coloured PETG without loosing the Colour? Are there any Methods to Preserve or Regain the Colour? 5 days ago:
Soooo I did actually try Vapor Smoothing with MEK Before! Infact I still got a Litre of that Stuff Around now, but even after leaving the print in there for Days at 50°C the Results where… honestly no big Changes at all…
I do suspect there is an Error in my Methodology… but turns out there isnt a lot of Info out there on Vapor Smoothing with MEK… Have you used MEK for Vapor Smoothing before?
- Submitted 5 days ago to 3dprinting@lemmy.world | 27 comments
- Comment on Fuck. My. Life. 🙃 1 week ago:
3 Thoughts as I had simular Issues!
Is the Bed Leveling correct? A Loose Print Head can give false results, big issue I had once with my P1S.
Try Changing the width and Hight of the First Layer to smaller Values, no clue Why, but it Fixed this kinda issue before for me!
In Software, Is the Model Properly put on the Ground and not floating? Happened to me before, since Supports where turned off I didn’t notice it
- Submitted 4 weeks ago to animepics@reddthat.com | 0 comments
- I've Commissioned an Artist that I've been following for 7 Years Yesterday... 2 Hours Later, he was Done!!!lemmy.blahaj.zone ↗Submitted 4 weeks ago to animepics@reddthat.com | 0 comments
- Submitted 4 weeks ago to animepics@reddthat.com | 0 comments
- "Lyra's First Encounter with Earth Life" The Newest Commission of my Space Fox OC Lyra!lemmy.blahaj.zone ↗Submitted 3 months ago to animepics@reddthat.com | 0 comments
- Comment on Worth checking 3 months ago:
Man I wish this still was reliable. Especially with Art Generation they seem to have pretty much fixed that happening and or found promps to hide it. The only way I’ve found to recognize it on the quick is by looking for words or symbols, those still seem notably jank… who knows how long this will stay reliable for…
- Comment on I'm Unable to get any PETG HF Filament to Stick on the Bed after having Switched from a 0.4mm to a 0.2mm Nozzle [Bambu P1S] 4 months ago:
Oooo I will try that now yes
- Comment on I'm Unable to get any PETG HF Filament to Stick on the Bed after having Switched from a 0.4mm to a 0.2mm Nozzle [Bambu P1S] 4 months ago:
Hm I see, if anything im glad to not be the only one with such Oddball issues! I’ll keep my expectations at bay incase this does end up hopeless
- Comment on I'm Unable to get any PETG HF Filament to Stick on the Bed after having Switched from a 0.4mm to a 0.2mm Nozzle [Bambu P1S] 4 months ago:
I can try to messure my Filament, tho this would suprise me as the same Filament works just fine with the 0.4mm Nozzle. I doubt that the Nozzle itself is clogged as it is Brand new and freshly build in
- Comment on I'm Unable to get any PETG HF Filament to Stick on the Bed after having Switched from a 0.4mm to a 0.2mm Nozzle [Bambu P1S] 4 months ago:
While that will definetly help for my Current project, I do wanna get to the bottom of why it stopped working and fix it once and for all!
- Submitted 4 months ago to 3dprinting@lemmy.world | 14 comments
- Submitted 4 months ago to 3dprinting@lemmy.world | 14 comments
- Submitted 4 months ago to retrocomputing@lemmy.sdf.org | 8 comments
- The Commission for my First ever OC just got done! May I present you: Lyra Vulpecula, The Cosmic Fox!lemmy.blahaj.zone ↗Submitted 5 months ago to animepics@reddthat.com | 2 comments
- Comment on Anker is no longer selling 3D printers 5 months ago:
Ah a Shame, I was always interested in the M5
- Comment on What anime character, you wish had more merch? 5 months ago:
Senko definetly. Imagine a Statue with an Actually Fluffy and Soft Tail!
- Submitted 7 months ago to 3dprinting@lemmy.world | 2 comments
- Comment on Slavic dress Ran 9 months ago:
God damn thats beautiful
- Submitted 9 months ago to 3dprinting@lemmy.world | 11 comments
- Comment on You guys have to end it 10 months ago:
• Wanted to Start on a Steep Hill? We had a Tool for that: it was Called “Flooring the Gas while letting go off the Clutch”
I miss the Smell of Burned Clutch…
