Rutty
@Rutty@sh.itjust.works
- Comment on Philips debuts 3D printable components to repair products 1 week ago:
I was thinking about 3D printing guards just the other day. It might be worth doing
- Submitted 1 month ago to 3dprinting@lemmy.world | 1 comment
- Comment on (Troubleshooting) Advice for improvement 2 months ago:
Interesting, so best practice is to increase layer height for PETG. Seems good to know
- Comment on Alien planter head 2 months ago:
How it’s looking from a distance:
- Submitted 2 months ago to 3dprinting@lemmy.world | 8 comments
- Comment on (Troubleshooting) Does anyone have an elegoo giga? 2 months ago:
I might have to try some of this buildtak.
- Comment on (Troubleshooting) Does anyone have an elegoo giga? 2 months ago:
I think you’re right on the suggestion. It’s not enclosed and in a garage. That seems a good place to start.
Thank you.
Also what’s ringing?
- Comment on (Troubleshooting) Does anyone have an elegoo giga? 2 months ago:
There’s no enclosure currently. It sounds like this is likely the culprit. It’s currently in a garage that isn’t very temperature controlled atm.
I don’t know about enclosure temps, but it will bet from around 55-72 F depending on time on day right now.
- Comment on (Troubleshooting) Does anyone have an elegoo giga? 2 months ago:
I think you might have nailed it on advice. Based on what you and others are saying it sounds like an enclosure is in order.
I was wondering about glue? I’ve been using it on the build plate on the giga. To be honest though, I don’t even bother gluing pla or PETG prints on my smaller printers that have textured PEI build plates.
Understandably though, it makes sense the larger build area and lack of enclosure would make adhesion more difficult.I noticed a bit of wobble when it was printing the arches at higher heights. I think you are again right in that speed needs to be reduced.
- Submitted 2 months ago to 3dprinting@lemmy.world | 10 comments
- Submitted 2 months ago to 3dprinting@lemmy.world | 3 comments
- Submitted 4 months ago to [deleted] | 20 comments
- Comment on flouride 5 months ago:
Okay fluoride gang (of which I may be a member)…
A study about the affects of fluoride in municipal water in plants: MSU study
- Comment on Just started printing with ABS.... 5 months ago:
White ABS is a classic
- Comment on Update on Menippus planter 6 months ago:
I think maybe Sainsmart. They also do bad toy, so maybe source was the problem.
How do you handle fumes with ASA? they are much worse than ABS, imo.
- Comment on Designed this coaster, because I wanted something tidy looking and dual color, without filament changes 6 months ago:
Hey! I was thinking about doing this.
Any useful info, should o give it a go?
- Comment on Update on Menippus planter 6 months ago:
Essentially. I was growing oregano, basil, flowers, and thyme in others.
- Comment on Update on Menippus planter 6 months ago:
Printed right side up. Everything was achieved via support setting optimization, and heated support removal where necessary (nose and lip in particular).
PLA holds up alright, but it’s gets brittle. There are just better choices.
Interesting point about the ABS, it appears to be holding up very good, but I’ll monitor it overtime.
- Comment on Update on Menippus planter 6 months ago:
ABS is nice, PETG good, ASA hard to print, PLA holds up, but don’t recommend.
- Submitted 6 months ago to 3dprinting@lemmy.world | 7 comments
- Comment on Lifestyles of the Bronze Age Famous 6 months ago:
I have plastic vases that can have them on them. Should take 3 days total
