Comment on Virgin Media Warns UK Broadband Users Not to Switch Routers Off at Night - ISPreview UK
ulterno@lemmy.kde.social 1 month ago
Read the title and went: What? They want you to keep your network hardware ON, when unattended, to increase the undetected malware entry opportunities?
Turns out it as their own devices they wanted to push updates to.
I would really prefer to use my own device though and even better, configure it myself after learning how the ISP’s network works. But convenience is hat it is.
Yep, after moving from Germany to the UK I was pretty surprised that in the UK you’re not supposed to get this kind of information from your ISP.
In Germany you can get your own DSL/cable/fibre modem and your ISP has to give you the necessary information to get these devices into their network.
you’re not supposed to get this kind of information from your ISP
Wait, do you mean, it’s illegal to ask for it?
Not illegal, but the ISPs are seemingly under no obligation to give you those details. In Germany, there’s the “freedom of routers” embedded in the telco law. So they HAVE to give you everything you need to get your custom router online via their wire/fibre.
Bridge mode is just using the ISPs router and bridge that into your router. It’s not the same - you still need the ISP’s access device instead of just yours.
Not illegal, but the ISPs are seemingly under no obligation to give you those details. In Germany, there’s the “freedom of routers” embedded in the telco law. So they HAVE to give you everything you need to get your custom router online via their wire/fibre.
OIC, so, same as here. Germany seems to be having pretty well made laws in these cases.
Bridge mode is just using the ISPs router and bridge that into your router. It’s not the same - you still need the ISP’s access device instead of just yours.
Except that it is a layer 2 bridge and I couldn’t connect to the network directly, either way, because their line is copper ^[Image] and consumer routers/modems are usually RJ45/RJ11.
Most providers in the US allow it too. It’s great that Germany has it enshrined in law, but in practice it’s not the exception.
It’s been allowed everywhere I have ever lived in the US.
The issues you’ll run into is they get all stupid about it if your service ever goes down. They’ll always blame your router/modem first. (Literally the entire neighborhood could be down and they’ll act like it’s something specific to your device). Sometimes they try to charge an install fee or a connection fee or other dumb shit.
I think their are local laws that require them to allow byod too. It depends on your area though.
Here is literally no different.
It’s only Virgin Media to my knowledge who does this.
Most of the other providers are happy for you to use anything that works properly for VDSL or FTTP.
Most FTTP providers fit an ONT that puts the connection back into an RJ45 ethernet connector.
Then you connect to the provider using PPPOE. Anything past the ONT, you can do whatever you like.
you don’t need to know how the ISP network works, you only need some networking concepts. Subnets/addressing and very basic routing (for a basic setup). You won’t even need firewall rules if you don’t host anything at your place (that needs to be accessed from outside)
Sorry. I’m addicted to knowledge. I need to know.
Chad
CameronDev@programming.dev 1 month ago
The malware argument is a bit weak, if your router is vulnerable to something it’ll likely be found and pwnd in a matter of minutes, so turning it off a night won’t really save you. And once a patch is released, it’ll be reverse engineered in a few hours/days, so ideally you want patches as soon as they are released.
Using your own device is usually a good idea anyway, telco stuff is usually pretty mediocre. And as soon as your device is slightly custom, it becomes a less valuable target.
ulterno@lemmy.kde.social 1 month ago
It’s much more than just a bit weak, unless you are somehow continuously monitoring it, so yeah, in most end-user scenarios, it would hardly make a difference to keep it on, even if there were no updates.