nieceandtows
@nieceandtows@programming.dev
- Comment on Trying to design a simple photo frame. Please help me understand these print issues. 1 week ago:
I tried building this, and accidentally created a black hole in my living room, it’s sucking everything in help!
- Comment on Trying to design a simple photo frame. Please help me understand these print issues. 1 week ago:
Could you point me to some images of the u shaped or triangular cross section? I’m having trouble visualizing it.
- Comment on Trying to design a simple photo frame. Please help me understand these print issues. 1 week ago:
Thanks for the pointers. I tried 45 print, and the vertical part broke off within the first inch or so lol. Should have tried at low speeds, because until it broke, it looked pretty good. May be that filet could have made it not break off that way.
- Comment on Trying to design a simple photo frame. Please help me understand these print issues. 1 week ago:
I definitely want to get better, which is why I’m asking for feedback on the model as well. Please give me some tips and tricks to think and plan for efficient models that are best suited for 3d printing. How would you recommend I modify this model?
- Comment on Trying to design a simple photo frame. Please help me understand these print issues. 1 week ago:
I tried with 50% speed, and even silent option which is even slower. Still happened. May be a hexagonal pattern might work better. I just want to build a simple photo frame that one can print without supports, and one that uses minimal filament.
- Comment on Trying to design a simple photo frame. Please help me understand these print issues. 1 week ago:
Yeah the front looks great, but I feel like it’s not good enough with an ugly back
- Comment on Trying to design a simple photo frame. Please help me understand these print issues. 1 week ago:
I was thinking of that before posting that, but wanted to check if it’s something wrong with my printer before that
- Comment on Trying to design a simple photo frame. Please help me understand these print issues. 1 week ago:
Printing the upright part flat on the bed is tricky, because it has a 0.75mm channel running through it for the photos. Wouldn’t that cause overhang issues, or is it too small to be a problem?
- Trying to design a simple photo frame. Please help me understand these print issues.programming.dev ↗Submitted 1 week ago to 3dprinting@lemmy.world | 22 comments
- Comment on Designed a simple photo frame on FreeCad. Why are some layers peeling in my print? 2 weeks ago:
It was printed lying down. I’ll add the model and slicer screenshot after I get home
- Comment on Designed a simple photo frame on FreeCad. Why are some layers peeling in my print? 2 weeks ago:
ah. I’ll try that, thanks.
- Comment on Designed a simple photo frame on FreeCad. Why are some layers peeling in my print? 2 weeks ago:
sorry, ender3v3 corexz, polyterra matte pla, 0.4 mm nozzle size
- Submitted 2 weeks ago to 3dprinting@lemmy.world | 20 comments
- Comment on Bethesda announces a new Fallout... reality show 3 weeks ago:
I’m bummed there’s no good single player fallout after fallout 4.
- Comment on [deleted] 3 weeks ago:
The ‘At Least’ is doing heavy lifting there.
- Comment on Is this noise normal? 3 weeks ago:
That makes sense, thank you.
- Submitted 3 weeks ago to 3dprinting@lemmy.world | 5 comments
- Comment on What does the bed mesh in Fluidd show? My prints are good, nothing to complain about, but I see the bed mesh doesn't look so good. 3 weeks ago:
Makes sense, thank you
- Comment on What does the bed mesh in Fluidd show? My prints are good, nothing to complain about, but I see the bed mesh doesn't look so good. 3 weeks ago:
It’s an Ender 3 v3 CoreXZ. The filament sensor is on the right side. It is possible that when it reaches the right most side, it ‘bends’ the pfte/cables to its maximum and they put a strain? If so, how do I remedy it?
- Comment on What does the bed mesh in Fluidd show? My prints are good, nothing to complain about, but I see the bed mesh doesn't look so good. 3 weeks ago:
how would I do that?
- Comment on What does the bed mesh in Fluidd show? My prints are good, nothing to complain about, but I see the bed mesh doesn't look so good. 3 weeks ago:
- What does the bed mesh in Fluidd show? My prints are good, nothing to complain about, but I see the bed mesh doesn't look so good.programming.dev ↗Submitted 3 weeks ago to 3dprinting@lemmy.world | 12 comments
- Comment on How do I improve the overhangs on my Artillery Genius? 4 weeks ago:
I’ll try that thanks
- Comment on How do I improve the overhangs on my Artillery Genius? 4 weeks ago:
This is more to tweak/tune the printer to print better. I have an ender3v3, and I know it can print it without supports fine, so trying to figure out why this one can’t
- Submitted 4 weeks ago to 3dprinting@lemmy.world | 8 comments
- Comment on Is this nozzle too low or bed temperature issue? 4 weeks ago:
Makes sense, thanks for the picture. Is there a trick to the right friction when using the paper method?
- Comment on Is this nozzle too low or bed temperature issue? 4 weeks ago:
Thanks for the feedback. I’m doing it by the paper method, so I might be guessing the right amount of friction wrong. Is there a trick to figuring out the right amount of friction using the paper?
- Comment on Is this nozzle too low or bed temperature issue? 4 weeks ago:
Yeah looks like the plate was not fully flat to begin with. Making it attach fully flat to the glass bed made things a lot better Image
- Comment on Is this nozzle too low or bed temperature issue? 4 weeks ago:
Yeah turns out the plate got bowed during shipping and was not exactly flat. After making it flatter and some cleaning, it’s looking a lot better. Image
- Comment on Is this nozzle too low or bed temperature issue? 4 weeks ago:
The default glass bed works perfectly at 60. I’m wondering if there’s a temperature difference between the glass plate below and the pei plate above.
