UserNotFound

@UserNotFound@lemmy.world

• ⁨Comment⁩ on ⁨What's the best game you played this year (that didn't come out this year)?⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  Probably Mass Effect Legendary Edition

• ⁨Comment⁩ on ⁨Finally finished my first RC car⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  It’s recommended to use PC or ASA for motor parts. I used ASA

• ⁨Comment⁩ on ⁨Finally finished my first RC car⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  PLA Prusament Lipstick Red (body) Polyterra Charcoal Black (chassis) Polyterra Fossil grey (inside) Filament PM(Czech brand) graphite black (seats) Filament PM white Filament PM Pearl Red (cage)

  ASA Prusament Lipstick Red (for few parts)

• ⁨Comment⁩ on ⁨Finally finished my first RC car⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  I see, thanks for explain.

  Driveline is no need to lubricate, because it’s belt drive system. Parts fit well, bearings, belts etc (although, that depends on how well calibrated is your printer). I think that system is strong enough. I built it with brushless motor and it’s wild.

  Only challenging parts were ball joints. I had problems to fit them in place, but I found a way.

• ⁨Comment⁩ on ⁨Finally finished my first RC car⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  There is belt gearbox, I found belts in my local shop. Or how did you mean your question? I found all in non printed parts bom

• Finally finished my first RC carlemmy.world ↗
  Submitted ⁨⁨1⁩ ⁨year⁩ ago⁩ to ⁨3dprinting@lemmy.world⁩ | ⁨9⁩ ⁨comments⁩
• ⁨Comment⁩ on ⁨xkcd 2830: Haunted House⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  Laughing in Europe

• ⁨Comment⁩ on ⁨Plate difference⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  It’s called effiency

• ⁨Comment⁩ on ⁨Plate difference⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  Very much. Can print bigger projects, or smaller one with more parts on the same plate (for example, rims for rc car)

• Plate differencelemmy.world ↗
  Submitted ⁨⁨1⁩ ⁨year⁩ ago⁩ to ⁨3dprinting@lemmy.world⁩ | ⁨7⁩ ⁨comments⁩
• ⁨Comment⁩ on ⁨3D printed Portal coasters⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  Image

• ⁨Comment⁩ on ⁨Finished building the MK4 kit and placed it in the enclosure, first few prints have been great.⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  I was thinking about the weight. Anyway, thanks for the info

• ⁨Comment⁩ on ⁨Finished building the MK4 kit and placed it in the enclosure, first few prints have been great.⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  Is it safe to put dryer with filament on top of the box? I have Tukkari for my Mini and I haven’t try that yet