I’ve recently become the owner of a home that was constructed in the mid 1950s (in the US). As such, not all the outlets are grounded, three-prong receptacles, since that wasn’t code-required at the time. It looks like a few have been added or upgraded over the years, but there are still many that are ungrounded. What is the best way to go about converting those receptacles to be grounded? Will that require a professional? It seems like probably the kind of electrical work that I am capable of doing myself, but I am also very much not an electrician.
Depending on how they ran the wire and the type of wire it may not require a professional but if you dont feel comfortable doing the work there is nothing wrong with hiring an electrician.
To verify if a ground wire was run, there are two things you can do:
- Check existing receptacles
This means turning of a receptacles at the breaker, removing the cover and pulling the receptacles out of the box to look at the wire run. If it has a black/white and bare copper (or copper clad aluminum) then there is a ground wire in the box. If you dont see a bare copper wire or if the wire was cut short at the point the wire enters the box then an electrician is probably required.
- Check the breaker box
To check your breaker box, flip the main breaker that runs service to your house. It should be the 50/100/200 amp breaker at the top that is not part of the column of smaller breakers. Then remove the cover around the breaker box to expose the wiring inside the box. All the wires from your house should run into this box and if you have ground wires they should be connected to the ground bus inside the breaker. Again you should see lots of black/white wires and bare copper wires that are ground wires. If they are all cut at the point the cables enter the box you will probably need to run new wire and that will require an electrician.
Shimitar@downonthestreet.eu 8 hours ago
First of all make sure you do have a real ground, as in these cases most probably they only added a three prong receptacles wothout the third wire.
And even of the ground wire is there, follow it all the way… Since o have seen that dangling unconnected so many times…
Is this a home or an apartment? '50s apartment buildings most probably don’t even have a common ground at all.
compostgoblin@lemmy.blahaj.zone 8 hours ago
It’s a single family residential home. I’d hazard a guess that there isn’t a ground wire, but I’ll take a look.
In the event there isn’t a ground wire, it sounds like my options are 1) rewire with the ground wire included or 2) install GFI outlets (circumventing the need for a ground wire). Is that right?
blargh513@sh.itjust.works 7 hours ago
Get a small voltage tester. All it needs to have is two wires and a little light. They sell them at any hardware store.
Go find one of your three prong outlets. Look at the two slots. If the ground pin is at the bottom, the left slot (taller than the right) is the neutral, should have a white wire. The shorter slot on the left is hot.
Try your tester by putting one of the probes in the neutral and one in the hot. It should light up.
Now put one in the ground pin hole and the other in hot. If its grounded, the tester will light. If it does not, that ground is not connected to anything.
Word of caution: some jackasses will connect the neutral to the ground on the back of the outlet. This is stupid and dangerous, but it will pass a quick test like the one we did. You should take at least one of the three prong outlets apart and check. If they did it once, they probably did it many times.
Turn off the power to that outlet (use your new tester to verify that the power is off) and pull the outlet apart. You might get lucky and find that the wiring had a ground wire (bare copper wire) that was just tucked away. You can just get a proper grounded outlet and attach the bare wire to the green screw.
Before you pop the bubbly if you find that bare copper wire, you need to test it again. With the outlet pulled out (leave wires connected to original outlet) probe the hot (black) wire and touch the bare copper ground wire. The tester should light up. If it does not, the copper ground wire is not connected to the ground in the breaker box (or in some older homes, the ground wire is connected to copper plumbing).
If the ground does not work, you can go on a hunt to find out why. Most houses, one outlet will daisy chain to another. If an upstream outlet has ground wires, but were not connected, that will be a problem. You can work your way backward to see if you can find and connect them all. If you’re taking the outlets apart, you may as well expect to do this anyway.
If the ground was tied to plumbing and someone replaced a copper section with a nonmetallic (pex, PVC) the ground will no longer work.
I would advise to at least try to figure out what is going on. You’ll learn a lot in the process and as a homeowner, its really important to understand your electrical system. Open a few outlets and probe (carefully). If you hit the wall, you may need to get an electrician in. They can probably tell you what’s up and then you can do the gruntwork of rewiring outlets.
Shimitar@downonthestreet.eu 5 hours ago
Setting up a ground system isn’t that hard, it involves bury a few rods and do some wiring. I did it for my house, but I had an electrician expert tell me what to do and how yo do it properly.
Said so, get ground wires absolutely and a ground “stuff” (not native English speaker don’t know the correct word).