Handyman suggested cutting hole in 1330 sq. ft. attic for second attic ventilator. Does this make sense?

Submitted ⁨⁨2⁩ ⁨weeks⁩ ago⁩ by ⁨TheDorkfromYork@lemm.ee⁩ to ⁨[deleted]⁩

General info: Looking to get current attic ventilator fan replaced. The attic is about 1400 sq. ft. Current attic ventilation fan is a foot from the ridge of the roof. Live in USA.

Handyman wants: To install two 1500 CFM fans. Two 120 volt 20amp dedicated circuits, one for each fan. He wants to install the second fan 4 feet away from the current fan. He stated that the attic ventilator fan would need to be replaced within 6 years.

My questions: Would two fans be better than one fan? Would I need two 120 volt circuits to run two fans? Is there an attic ventilator that has a user replaceable fan?

Thank you in advance for any help.

source

Comments

Sort:hotnew top

stands_while_poops@lemmy.world ⁨5⁩ ⁨days⁩ ago
3000CFM is probably too much. Your exhaust needs to match your soffit intake in terms of how much air they move. You can’t just exhaust air without replacing that air. Find a roofing contractor and not a handy man.

source
protist@mander.xyz ⁨2⁩ ⁨weeks⁩ ago
What reason does your handyman give for needing a second fan in your attic? What’s going to be different for your house? I’m assuming your attic is a typical uninsulated attic in the US. I live in Texas, and as far as the eye can see there 70s-90s builds with uninsulated, passively-ventilated attics. I have a thick layer of blown-in insulation up there, and with the volume of air your handyman wants to move, I’d be concerned the insulation would move with it.

In an ideal world, all our attics would be inside the insulated envelope of our homes, but our building standards are not there. So where you can affect energy efficiency is in improving the impermeability of your insulation as it currently exists. If you’re going for energy efficiency, slightly lowering the ambient temperature of your attic in the summer heat is just not an effective solution. Spend that money instead on fully sealing all the holes around joints and fixtures that are currently leaking air between your living space ceiling and your attic, and improving the R value of your attic insulation.

I don’t know if what I’m talking about applies to your house, but if so, check out this Matt Risinger video for a lot more detail.

source
- TheDorkfromYork@lemm.ee ⁨2⁩ ⁨weeks⁩ ago
  First off, thank you for the advice.
  
  The reason the handyman gave for installing two fans was basic, to improve the dispersal of hot air. My partner and I concluded that removing heat would be the most effective first step to decreasing the temperature of the house, but we can be talked into considering insulation first. We’ll look into leak patching and into insulation.
  
  Do you happen to know if during the winter months, if insulation would significantly block the house from being heated by the sun? We are looking to get a heat pump in the long run and originally planned to have the insulation done at the same time, but in the meantime, winters can get cold here and any heat we get goes a long way.
  
  source
  - stands_while_poops@lemmy.world ⁨5⁩ ⁨days⁩ ago
    If you’re gaining heat from the winter sun you’re likely losing more heat than you’re gaining from poor insulation.
    
    source
    -> View More Comments
  - protist@mander.xyz ⁨2⁩ ⁨weeks⁩ ago
    Improving the insulation barrier between your ceiling and attic will only serve to increase your home’s heat retention in the winter. When it’s cold outside, the sun heating your attic is not going to increase the heat in your home more than the cold ambient temperature in your attic is going to decrease it. Before you pay to have this work done I’d genuinely consider whether there are other projects that would be much more impactful you could do instead. Definitely get other opinions from contractors first (never just get one quote for any project, prices and recommendations can vary widely) and see if you can get a certified home performance contractor to take a look at your goals
    
    source
pdavis@lemmy.world ⁨2⁩ ⁨weeks⁩ ago
I thought ridge vents were all the rage these days. I installed ridge vents and then put up Reflectix Reflective Roll Insulation from the soffits up to 12-18 inches from the ridge. It reduced the heat in the attic by a noticeable amount and wasn’t too expensive or difficult to install. I also blew in additional insulation. I plan on adding additional venting in the soffits in the future. My experience is that fans fail, require maintenance, use energy, and tend to only cool the attic off in certain areas if not well planned out with supporting architecture and venting.

source
Acedia@lemmy.world ⁨2⁩ ⁨weeks⁩ ago
Depends on the cfm (cubic feet per minute) of the fan. This will tell you how much it’s working to replace the air in your house.

Also depends on your current circuit, and your circuit current, lol. I’m willing to bet that the current circuit is 20amp, so I don’t know why he’s trying to replace that. I’m willing to bet the fan is also using almost all of the available circuit. You need to find out what the draw is on the fan for that. A 20amp circuit can handle 2400 watts. But due to code limiting draw at 70%, you can only put 1680w on there legally. That’s for saftey(fire) reasons.

source
- TheDorkfromYork@lemm.ee ⁨2⁩ ⁨weeks⁩ ago
  Each fan would be 1500 cfm. I’m guessing the attic is about 3500 cubic feet.
  
  I forgot to say this, but the current circuit, as far as I can tell, doesn’t connect to the breaker box. The lines are dead and the attic ventilation fan hasn’t worked since we bought the house. The fan doesn’t spin smooth when manually rotated, so we assumed it needed replacing.
  
  The handyman originally insisted on installing a 240 volt wiring and circuit breaker. I don’t know much about electricity but that set off red flags. I have no problem going with higher gauge wiring if the cost is cents more, but there is no reason to run that many amps unless we’re plan on charging an electric car in the attic.
  
  Thank you for your comment.
  
  source
  - apfelwoiSchoppen@lemmy.world ⁨2⁩ ⁨weeks⁩ ago
    Yeah, that 240v line run suggestion puts a gigantic question mark on anything they’ve suggested at all.
    
    source
    -> View More Comments
- Acedia@lemmy.world ⁨2⁩ ⁨weeks⁩ ago
  Also, is this supposed to replace the air in the house, and attic? Because 3000cfm is akin to a wind tunnel. That would replace the air in an attic and house in about a minute. Without proper air exchange points, that actually sounds problematic to seals.
  
  source
  - TheDorkfromYork@lemm.ee ⁨2⁩ ⁨weeks⁩ ago
    The fans only would remove air from the attic. I didn’t consider the seals. I’ll make sure to bring up the air exchange points when I talk to the handyman again, but I’m considering dropping him. Thank you for your comment.
    
    source
    -> View More Comments