Comment on Opened an old scientific instrument to see if it works...

• Aceticon@lemmy.world ⁨1⁩ ⁨day⁩ ago

  If I remember it correctly, it’s not just the overall capacity but also the how much the voltage drops as the current being drawn goes up (i.e. their internal resistance).

  You can pull several Amps out of an AA without its voltage dropping significativelly though it does accelerate depletion quite a lot if you do it in a sustained way (the volage curve of alkaline batteries actually depends on how much current you draw so if you just draw at say 100mA the “knee” in the curve were the voltage drops down from around 1.5V to a value too low to be useful is a lot sharper whilst if you draw 1A it’s a lot softer with the voltage starting to sinking much sooner for the same fraction of total charge drawn).

  Or in other words, the 9V battery might no be able supply enough peak current whilst still remaining close enough to 9V.

  (It was actually quite a commonly reported problem in Arduino forums that people used 9V batteries for things like motors and then had weird power drops or the motors didn’t actually work as expected even though theoretically everything seems to be in spec for them)

  You should probably test the device under “in use” conditions with a 9V battery rather than just in standby before you replace the current setup with a single 9V battery.

  source

  • troyunrau@lemmy.ca ⁨1⁩ ⁨day⁩ ago

    I appreciate your caveat about peak load. Fortunately for this device it is largely irrelevant. It’s so old school and analogue that there isn’t a standby draw – it’s either on or off. Its operational time is measured in days on a single 9V.

    It might be interesting, so I’ll describe the instrument. Starting with some VLF background:

    There are a number of VLF stations scattered around the world – for example station id NAA in Culter, Maine (24.0kHz) – used to communicate with their submarines while submerged. If they only transmitted when they had something interesting to say to the subs, that would be useful information to an enemy. So they have to transmit continuously (except for on scheduled maintenance days for the transmitters). These are very powerful huge antennas, often spanning entire valleys – after all, the wavelength at 24kHz is enormous. Different stations have different frequencies and we know about most of them.

    At a sufficient distance away from these antennas, all incoming signals are polarized due to reflecting off the ionosphere. These radio waves pass over linear conductors in the ground which will distort the polarization. What we’re effectively measuring is the distortions in these incoming radio waves to map the locations (and orientations) of linear conductors (natural antennas) in the ground, up to about 250m below surface.

    So this device is used to measure the incoming signal direction and polarization. It does so by setting up a harmonic oscillation on the device and emitting a tone. There’s a couple of magnetic coils on the device, and as you swing the device about, the received signal from the transmitter and the onboard oscillator will constructively or destructively interfere, changing the tone. You note the direction the tone is the strongest using a compass and inclinometer (both analogue) and write it down in a notebook. Then move to your next position and repeat.

    Prospectors have been using this for five decades at least.

    But as you can see, not a complicated thing from an electronics perspective. The only complicated thing is tuning the on-board oscillator properly.

    source

    • Aceticon@lemmy.world ⁨23⁩ ⁨hours⁩ ago

      Yeah, that’s quite shrewd way of going about it.

      Since it’s not emitting anything the power it needs will be way less that something emitting its own signal and then checking for bounces which is how I naveivelly expected it would work.

      Cheers for the detailed explanation.

      source

      • AnarchistArtificer@slrpnk.net ⁨22⁩ ⁨hours⁩ ago

        I have a running list where I have been collecting words that I like for the last few years.

        “Shrewd” is a good word and it’s going on my list. Thank you for the contribution.

        source

        • -> View More Comments