GingeyBook
@GingeyBook@lemm.ee
- Comment on Consumer, we have detected that you are above the poverty line. The 99¢ price printed on this Arizona tea can only applies to those below the poverty line. Your total comes to $3.67. 3 months ago:
At least with Kroger you don’t have to have the app, you can use their website for everything
- Comment on Wood smells like we should be able to eat it, but we can't. 4 months ago:
Or a Rice Crispy if you’d rather
- Comment on How long would it take to create a Pyramid today? 4 months ago:
Is a joke, but wasn’t sarcasm so didn’t include/s
- Comment on How long would it take to create a Pyramid today? 4 months ago:
Pretty sure Joe Rogan said it’s impossible to do today…
- Comment on How often do you use the small pocket inside your jeans pocket (if you have it) ? and what for ? 6 months ago:
Not the small pocket on jeans, but I do have some pants and shorts that have a small pocket fully inside the other pocket that I like to put my keys in
Keeps them from rattling around and scratching things
- Comment on Why does my printer suck so much? 8 months ago:
I’ll try increasing the heat, I run 200/60
- Comment on Why does my printer suck so much? 8 months ago:
At this point I’m counting down the days until it’s time to replace this one.
Totally killed this hobby
- Comment on Why does my printer suck so much? 8 months ago:
I have the bed and nozzle when calibrating z offset and bed tramming and auto bed leveling.
What’s the correct way for each of those?
- Submitted 8 months ago to 3dprinting@lemmy.world | 29 comments
- Comment on A top auto safety group tested 14 partial automated systems — only one passed 8 months ago:
Am I blind? What on earth does A M P and G mean
- Comment on What would be a good glue to repair this spatula with that wont he toxic or come undone in a dishwasher? 8 months ago:
That middle one acting kinda sus ngl
- Comment on Walmart in talks to buy Vizio for more than $2 bln, WSJ reports 9 months ago:
Yep we bought one in 2020, that thing sucked .
Switched to Sony recently and couldn’t be happier. Granted there are still ads but at least the UI is fast and responsive
- Comment on Vizio settles for $3M after saying 60 Hz TVs had 120 Hz “effective refresh rate” | Vizio claimed backlight scanning made refresh rates seem twice as high. 10 months ago:
Had nothing with bad “luck” with LG.
Sony is the way
- Comment on Redditor finds heavy block of iron shavings inside cheap PSU, also appears to lack safety protections 11 months ago:
But now I have to give Reddit traffic.
I’m conflicted
- Submitted 11 months ago to meta@lemm.ee | 5 comments
- Comment on What Are Your Favorite Hidden Gem Android Apps with Less Than 1 Million Downloads and 4+ Star Ratings? 11 months ago:
Small caveat, not available on latest version of Android
- Comment on Why am I having to level my Ender 3 s1 after every print? 1 year ago:
I am heating before I level, I’ve spent many many hours on it today and finally got something
Depending on how it goes when this print finishes I might switch back to the springs
- Comment on Why am I having to level my Ender 3 s1 after every print? 1 year ago:
The S1 comes with a CR Touch already installed, still have the problem
- Comment on Why am I having to level my Ender 3 s1 after every print? 1 year ago:
I’ll give this a shot, I was under the impression that you start with them as uncompressed as possible
- Comment on Why am I having to level my Ender 3 s1 after every print? 1 year ago:
That’s what I was wondering, it’s a pretty large print taking up most of the build plate. Since the bed is magnetic it takes a little bit of work to get it off
- Comment on Why am I having to level my Ender 3 s1 after every print? 1 year ago:
The bed is completely heating before each print, I just about always let it preheat and do something else before I start the print
It is not enclosed, would that make that much of a difference? I’m talking like one print turns out great for the entire duration and then I go to print again and the first layer won’t even stick.
Not sure what you’re even asking with the other questions about slop, backlash, and z tilt. Will have to look into those
- Submitted 1 year ago to 3dprinting@lemmy.world | 15 comments
- Comment on I downgraded to an iPhone 11 Pro Max – and I'm not missing much 1 year ago:
Lmao let’s not pretend like Android is winning in the support department.
- Comment on The Chinese calendar is 4721 years old. Did it have the same problem as the Julian calendar with an imprecise number of days per year? 1 year ago:
- Comment on I somehow got addicted to making phone cases for friends and family since I successfully printed TPU the first time. 1 year ago:
How well does the Lego one work with actual Lego bricks?