Tarnaq

@Tarnaq@lemmy.world

• ⁨Comment⁩ on ⁨Prints have a ridge⁩ ⁨⁨11⁩ ⁨months⁩ ago⁩:

  So pausing the print appears to be the issue. I printed 3 minis today without pausing, and they all came out perfectly.

  Thank you for all the responses!

• ⁨Comment⁩ on ⁨Prints have a ridge⁩ ⁨⁨11⁩ ⁨months⁩ ago⁩:

  Suction cupping could be a possibility on the sphere, it does not explain why I had ridges on miniature prints.

• ⁨Comment⁩ on ⁨Prints have a ridge⁩ ⁨⁨11⁩ ⁨months⁩ ago⁩:

  I’m hoping that’s the issue. I’ll find out tomorrow, and if not then I’ll look into the z axis.

• ⁨Comment⁩ on ⁨Prints have a ridge⁩ ⁨⁨11⁩ ⁨months⁩ ago⁩:

  I’ve paused all the prints I’ve done (I’ve only had the printer for about a month), I’m hoping that’s the issue. If not I’ll definitely look into the z axis screw.

• ⁨Comment⁩ on ⁨Prints have a ridge⁩ ⁨⁨11⁩ ⁨months⁩ ago⁩:

  I updated to the newest firmware before I started printing (I’ve only had it for a month or so).

  I’ll try without the pause, and then look into the z axis of that doesn’t solve the problem.

• ⁨Comment⁩ on ⁨Prints have a ridge⁩ ⁨⁨11⁩ ⁨months⁩ ago⁩:

  I don’t think it’s the render, there’s no ridge on the model when I’m supporting or slicing.

• ⁨Comment⁩ on ⁨Prints have a ridge⁩ ⁨⁨11⁩ ⁨months⁩ ago⁩:

  I generally have my lift set to 7mm, which should be enough. If it continues even if I don’t pause the print, I’ll give it a try.

• ⁨Comment⁩ on ⁨Prints have a ridge⁩ ⁨⁨11⁩ ⁨months⁩ ago⁩:

  That’s what I’m beginning to suspect, other prints that have had ridges or offsets I paused as well.

• ⁨Comment⁩ on ⁨Prints have a ridge⁩ ⁨⁨11⁩ ⁨months⁩ ago⁩:

  It’s not supposed to be there, there was no ridge when I was supporting and slicing.

• ⁨Comment⁩ on ⁨Prints have a ridge⁩ ⁨⁨11⁩ ⁨months⁩ ago⁩:

  It may be because I paused the print to check raft adhesion. I’ll try some prints tomorrow without pausing.

• ⁨Comment⁩ on ⁨Prints have a ridge⁩ ⁨⁨11⁩ ⁨months⁩ ago⁩:

  The preview does not have a ridge, nor was there one when I was supporting and slicing.

• ⁨Comment⁩ on ⁨Prints have a ridge⁩ ⁨⁨11⁩ ⁨months⁩ ago⁩:

  I should add that I’m using rafts and lifting the prints 5mm.

• Prints have a ridgelemmy.world ↗
  Submitted ⁨⁨11⁩ ⁨months⁩ ago⁩ to ⁨3dprinting@lemmy.world⁩ | ⁨29⁩ ⁨comments⁩