Matcraftou

@Matcraftou@lemmy.world

• ⁨Comment⁩ on ⁨Jesse is smarter than what we give him credit for.⁩ ⁨⁨11⁩ ⁨months⁩ ago⁩:

  Is this true??? If so WHY THE F… ARE WR STILL USING THE CURRENT CALENDAR.

  Honestly I would be all for a new calendar if this is true

• ⁨Comment⁩ on ⁨I am looking for a design for my ender3 V1⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  I am not asking for you to make one, I just search for one, I couldnt fidn anything exacly like this during my research

• I am looking for a design for my ender3 V1
  Submitted ⁨⁨1⁩ ⁨year⁩ ago⁩ to ⁨3dprinting@lemmy.world⁩ | ⁨2⁩ ⁨comments⁩
• ⁨Comment⁩ on ⁨Monitor Alignment Alignment Chart⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  I have chaotic good

• ⁨Comment⁩ on ⁨Ya gotta keep up with the times!⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  Especially the last one got me choking on air

• ⁨Comment⁩ on ⁨Weird PETG Behavior⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  No it’s just a stock sprite pro extruder upgrade kit that I bought directly form creality.

• ⁨Comment⁩ on ⁨Weird PETG Behavior⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  I already printed a temp tower and NO temps from 220 to 250 worked well

• ⁨Comment⁩ on ⁨Weird PETG Behavior⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  Oh I plan getting the dual z as well lol. I tried input shaping and pressure advance. As far as I am concerned I setup pressure advance and it has been going well.

  But with input shaper I did not manage to get it working, but in my current setup I believe it is unnecessary because my enclosure is FAR to wobbly and the printer vibrations goes to the entire house, I plan on printing springy feet and attaching the enclosure to the wall so that it does not move.

  So my vibrations is so bad that I need physical upgrades to even get it working… And an accelerometer

• ⁨Comment⁩ on ⁨Weird PETG Behavior⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  Oh don’t worry my z offset is set tight! And for the heat block I always undertihhgened and it leaked everywhere so now I tighten it firmly but not too much to the point of stripping the block

• ⁨Comment⁩ on ⁨Weird PETG Behavior⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  So for the mods:

  All in one rear mounted electronics box by Teaching Tech. Glass bed. Skr mini e3 v2. Sprite pro dd extruder. Klipper. Metal bed knobs and springs. PETG printed rear left tension remover. Crtouch. Ikea lack enclosure (not completely done YET). Others I might have missed so I guess it’s not important ¯_( ツ )_/¯

• ⁨Comment⁩ on ⁨Weird PETG Behavior⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  For the crash my hotend just untightened lowering it lower than the bltouch. I use klipper now so the mainboard firmware akaik isn’t responsible for a lot. I have done A LOT of mods which I will list in a reply. For manually level the bed, I just probe 5p times my bed with abl, look at the graph and adjust the knobs in consequence…

  Yeah I know it’s hard to troubleshoot without being there,trust me,trust me…

  Thanks for your help I guess my filament is better at 280C ¯_( ツ )_/¯

• Weird PETG Behavior
  Submitted ⁨⁨1⁩ ⁨year⁩ ago⁩ to ⁨3dprinting@lemmy.world⁩ | ⁨11⁩ ⁨comments⁩
• ⁨Comment⁩ on ⁨I miss 2011 memes⁩ ⁨⁨1⁩ ⁨year⁩ ago⁩:

  Wojakified