Comment on Got my first printer, what else do I need? Any tips on setup?
squaresinger@lemmy.world 1 week ago
In terms of physical things:
- Printer
- A roll of PLA (take it easy with buying filament. First figure out how much you will print, only then stock up in filament. Filament has a shelf life of 1-2 years depending on the type. Don’t buy too much or you might have to toss it. You can always buy more. Also, first master PLA, then get into other filaments.)
- A bottle of Isopropyl Alcohol (perfect print bed degreaser, makes your prints stick nicely to the print bed during printing)
- Pliers/tweezers/cutter knife to remove support and for simple post-processing
If you go more advanced (don’t do that in the beginning:
- Filament dryer (required for PETG, TPU and some other filaments, usually not required for PLA)
- First PETG, then TPU, then after filaments if you need them. I print since 2017 and PLA, PETG, TPU have been all I needed.
- Hot air soldering station (awesome tool for post-processing)
Software side:
- A slicer is a must. If there’s one that your printer’s manual recommends, get that one for the start. Otherwise get PrusaSlicer or Cura.
- 3D editing software or CAD software are required to DIY your own models, but there’s tons of models already available on the internet (checkout www.yeggi.com, it’s a 3D model search engine), so that’s not required in the beginning.
Btw, filament doesn’t need to be from your printer manufacturer. There’s lots of different manufacturers for filament. Just make sure the diameter is correct (usually 1.75mm) and that you shop for a material that’s compatible with your printer (PLA, PETG works on all printers; TPU/TPE requires a direct drive extruder which most printers have nowadays; ABS/Nylon requires an all-metal-hotend that can go over 260°C and an enclosure; Carbon-filled filaments require a hardened nozzle).
I personally like spectrumfilaments.com a lot if you are from Europe.
melsaskca@lemmy.ca 1 week ago
If the filament shelf-life is 1-2 years does that mean the piece it creates becomes more brittle or breaks down as well, after 1-2 tears. Novice here.
squaresinger@lemmy.world 1 week ago
On the one hand, yes, prints do age, on the other hand, the mechanical requirements for filament during printing are much more intense than on a finished part. So usually, unless they have to constantly resist mechanical load, UV or flowing water, printed parts usually last much longer.
The issue with filament is that it’s a rather thin strand of plastic that’s pulled with a lot of force, that’s being bent out of shape (by being unrolled) and then heated to 200+°C.
The kind of bending and pulling that filament has to survive by unrolling it from the spool is rare for finished prints, and melting in a way that it still sticks to a new layer afterward isn’t easy on the material either.
Some filaments (e.g. PETG, TPU/TPE, Nylon) are hygroscopic, so they draw water from the air. In a finished print that’s usually not a problem, but during printing it is, because when the water in the filament hits the hotend it’s instantly (and rather violently) turned into steam, which leaves small air bubbles in the extruded plastic like miniature swiss cheese. That causes stringing, bad layer adhesion and brittle and ugly prints.
You can still print old filament. You can dry hygroscopic filaments to get them better. But old filament will lead to weak and often ugly prints. The other day I printed with 4yo Silk PLA. It did complete the print, but there were multiple areas where the layers didn’t adhere and you could just pull the layers apart with very little force.
Some old filaments (especially PLA) become brittle like spaghetti. You try to unroll them and they just snap. Sometimes it’s only the outer layer, so you crack away a few rounds of spool until you end up on a deeper layer and find filament that still works.
So the 1-2 years isn’t a hard limit but a good guideline. No need to toss old filament that still works. You can still use old and bad filament for test prints or other garbage prints that don’t need quality.
But you should in general plan to consume your filaments within 1-2 years and not overbuy so that you are left with a ton of aging filament.
melsaskca@lemmy.ca 1 week ago
Thank you for taking the time to provide this very good information. All the best to you!